Crown CTS8200AUSPCN Powered Amplifier 8 Channels

Crown CTS8200AUSPCN


The Crown CTs 8200AUSP/CN power amplifiers have an integrated 3rd generation, DSP-based PIP (Programmable Input Processor) input module. It connects the amplifier to a 100 Mbps Ethernet network allowing it to be remotely controlled and monitored via System Architect software.



Crown CTS8200AUSPCN Powered Amplifier 8 Channels

FEATURES
 
  • 100 Mbps Ethernet single-plug solution for CobraNet audio, and HiQnet control and monitoring. 
  • Analog audio inputs allow CobraNet network audio input, CobraNet audio backup, or a hard-wire emergency override of CobraNet audio 
  • 24 bit digital to analog conversion with 32 bit, floating point DSP processing 
  • Up to 18 assignable filters per channel with 9 different filter types including all-pass filters 
  • Over 2 seconds of delay available per channel 
  • Input compressors and output limiters for each channel 
  • Dual, uncorrelated noise generators for noise masking 
  • Sine generator 
  • Load supervision 
  • Full error reporting 
  • Firmware upgrades via the network 
  • 10 user selectable presets 
  • Reliable FLASH memory backup of all parameters 


  • SPECIFICATIONS
       
    • Power Rating Dual, 8 Channels Driven: 
      200 Watts @ 4 Ohms(per channel) 
      160 Watts @ 8 Ohms(per channel) 
      200 Watts @ 70 Volts(per channel) 
    • Dual, 1 Channel Driven: 
      270 Watts @ 4 Ohms(per channel) 
      220 Watts @ 8 Ohms(per channel) 
      250 Watts @ 70 Volts(per channel) 
    • Bridge-Mono, 4 Channel Pairs Driven: 
      400 Watts @ 8 Ohms(per channel pair) 
      320 Watts @ 16 ohms(per channel pair) 
      200 Watts @ 100 Volts(per channel pair) 
    • Bridge-Mono, 1 Channel Pair Driven: 
      540 Watts @ 8 Ohms(per channel pair) 
      440 watts @ 16 Ohms(per channel pair) 
      250 Watts @ 100 Volts(per channel pair) 
    • Frequency Respones (at 1W, 20Hz-20kHz): +/-0.5dB 
    • Phase Response (at 1W, 10Hz-20kHz): +/-35� 
    • Signal To Noise Ratio below rated power (20Hz-20kHz): 100dB unweighted 
    • Total Harmonic Distortion (THD) at 1W from 20Hz-20kHz: <0.05% 
    • Intermodulation Distortion (IMD) 60Hz and 7kHz at 4:1, from 163 milliwatts to full bandwidth power: <0.05% (typical) 
    • Damping Factor: 10Hz to 400Hz: >180 
    • Crosstalk (below rated power, 20Hz to 1kHz): >80dB 
    • Common Mode Rejection (CMR) (20Hz to 1kHz): >50dB 
    • DC Output Offset (shorted input): <+/-5mV 
    • Input Impedance (nominal): 20 kilohms balanced, 10 kilohms unbalanced 
    • Maximum Input Level (before input compression): +20dBu 
    • Load Impedance (Note: safe with all types of loads): 
    • Stereo: 4/8 and 25 ohms (70V) 
    • Bridge Mono: 8/16 and 50 ohms (100V) 
    • Voltage Gain (at maximum level setting), 1.4V sensitivity: 
    • 4/8 ohm operation: 20:1 (26dB) 
    • 70V operation: 50:1 (34dB) 
    • 100V operation: 71.4:1 (37dB) 
    • Required AC Mains: 120V 60Hz, 220/230/240V/50 Hz 
    • Power Draw at Idle (120VAC mains, all channels in 4/8 ohm mode): 58W 
    • Power Draw at Idle (120VAC mains, all channels in 70V mode): 77W 
    • Cooling: Continuously variable speed forced air, front-to-back airflow. 
       
      DIMENSIONS & WEIGHT 
    • Unit: 19" x 5.25" x 16.25" (W x H x D) 
    • Weight: 36.6 lbs. 

    Similar Products


    RM1,219.00

    Behringer NX1000 1000W Powe...

    RM -

    Bose PowerShare PS604 Adaptable ...

    RM -

    Crown DCI4 1250N 4x1250W Networ...

    RM -

    Crown DCI8 300N 8x300W Network ...

    RM1,100.00 RM940.00

    Audio Center VA201 Power...

    RM -

    Crown IT4X3500HDB 4 Channels Po...

    See Also : Power Amplifier, Crown
    CONTACT US