Bose PowerShare PS604 Adaptable Power Amplifier EU

Bose PowerShare PS604 EU


Recommendation to performing arts venues, houses of worship, conference centers, retail stores, restaurants and bars and hospitality venues.



Bose PowerShare PS604 Adaptable Power Amplifier 


Bose PowerShare PS604 adaptable power amplifier delivers 600 watts for fixedinstall applications. Through patented technology, total amplifier power is shared across all output channels, allowing installers the freedom to utilize power where needed. With support for both low- and high-impedance loads up to 100V, PowerShare amplifiers adapt to a wide range of applications. Onboard configurable loudspeaker processing and direct access to zone controllers eliminate the need for an additional signal processor in many installations, while outstanding audio performance and reliability are assured with patented technologies inherited from the field-proven PowerMatch® line. This unique set of features and technologies makes PowerShare one of the most versatile highperformance amplifiers available.


Features 
• PowerShare Technology – Patented PowerShare technology allows the total 600 watts of power to be shared asymmetrically across all outputs, as each output is capable of delivering full power. Instead of selecting amplifier power based on the needs of the largest zone, installers now have the freedom to use total amplifier power in the application. This enables more flexibility during the initial design, or later on-site when making unplanned changes that take advantage of surplus power. 
• Load-Independent Outputs – Each channel can be configured for lowimpedance (4-8 Ω) or high-impedance (70/100V) applications without bridging, use of jumpers, or software settings. 
• DFL™ System – The Dual Feedback Loop system, inherited from the field-proven Bose PowerMatch® amplifier line, improves performance and reliability through continuous monitoring and control of both the current and voltage delivered to each output load. This combination provides improved linearity and lower distortion, while protecting loudspeakers. 
• Integrated Loudspeaker Processing with Optional PowerShare Editor Configuration – For applications requiring additional signal processing the PowerShare Editor Software offers real-time selection and control of Bose loudspeaker EQs, 9-band PEQs, standard mixing, crossover, delay, and mute/ output polarity through a USB connection. For basic setups without a PC, rear-panel settings allow installers to recall Bose loudspeaker equalization and protection per output channel. These features eliminate the need for an external signal processor in many applications. 
• ControlCenter Zone Controller Accessories – Bose ControlCenter CC-1 zone controllers can be directly attached for remote adjustment of amplifier outputs, further extending stand-alone amplifier applications.

Specification

 

Power Rating

 

Amplifier Power

4 x 150 W (THD+N < 0.04%, 1 kHz, 4-8 Ω, 70/100V)

Maximum Power per Channel

600 W @ 4-8 Ω, 70/100V

Gain (Low-Z mode)

32 dB

Gain (70V mode)

35 dB

Gain (100V mode)

38 dB

Audio Performance

 

Frequency Response

4-8 Ω: 20 Hz – 20 kHz (+/- 0.5 dB @ 1 W) 70/100V: Same as 4-8 Ω with 50 Hz high-pass filter

Channel Separation (Crosstalk)

> 85 dB @ 1 kHz, > 65 dB @ 20 kHz

Signal to Noise Ratio

100 dB (at rated power, A-weighted)

Audio Inputs

 

Input Channels

4 balanced

Connectors

12-pin Euroblock

Input Impedance

20 kΩ

Maximum Input Level

20 dBu (at 12 dBu sensitivity setting)

Sensitivity

4 / 12 dBu (low / high sensitivity)

Audio Outputs

 

Outputs

2

Connectors

8-pin inverted Euroblock

Integrated DSP

 

A/D and D/A Converters

24-bit / 48 kHz

Processing Functions

Standard mixer, loudspeaker EQ, 9-band PEQ, Vpeak/Vrms limiters, delay, band pass, mute/output polarity inversion

Loudspeaker Presets

Flat, DS16, DS40, DS100, FS3B, 402, 802, MA12EX, RMU105 and RMU108

Audio Latency

1 ms (any input to speaker output)

Indicators and Controls

 

Power LED

Solid green: Power is on. Blinking green: Unit is in standby mode. Solid amber: Thermal fault. Solid red: Supply fault.

Input Signal LED

Green: Signal present. Amber: Input is near clipping. Red: Input is clipping. Solid red: Indicates a fault..

Output Limit LED

Amber: Amplifier limiting an output. Blinking red: Amplifier muted. Solid red: Indicates a fault.

Controls, Front Panel

Power On/Off

Controls, Rear Panel

Amplifier mode DIP switches, loudspeaker EQ dials, output attenuators

Electrical

 

Mains Voltage

100 VAC – 240 VAC (±10%, 50/60 Hz)

AC Power Consumption

120 VAC: 79 W (Standby), 124 W (Max)

230 VAC: 88 W (Standby), 184 W (Max)

Mains Connector

Standard IEC (C14)

Maximum Inrush Current

14.14 A (230 VAC / 50 Hz), 8.04 A (120 VAC / 60 Hz)

Protections

High temperature, output short, extra high frequency (EHF), excessively low or high AC line voltage

Physical

 

Dimensions (H x W x D)

44 mm x 483 mm x 414 mm (1.7” x 19.0” x 16.3”)

Shipping Weight

7.8 kg (17.2 lb)

Net Weight

6.4 kg (14.1 lb)

Cooling System

Microprocessor controlled, variable speed fans, left to right air flow

General

 

Inputs (Control)

RJ-45 remote input for volume control using the CC-1 ControlCenter zone controllers, or for connection to the CV41. USB input for configuring the amplifier with PowerShare Editor software. Mute input control.

 



Similar Products

RM1,951.00 RM1,860.00

Crown XLI800 Power Amplifier 2 ...

RM -

Crown IT9000HD Powered Amplifie...


RM6,174.02

Crown CDI1000 275W 2 Channels P...

RM2,460.00 RM1,539.00

Tach PA250A Power Amplifier

RM1,500.00 RM938.00

Tach MU255A Audio Mixer


RM4,849.00

Crown XLS2502 2x775W 4ohm Power...

See Also : Power Amplifier, Bose
CONTACT US