Bose PowerShare PS602P Adaptable Power Amplifier UK

Bose PowerShare PS602P UK

Recommendation to performing arts venues, houses of worship, conference centers, retail stores, restaurants and bars and hospitality venues.

RM -

Bose PowerShare PS602P Adaptable Power Amplifier 

Bose PowerShare PS602P adaptable power amplifier delivers 600 watts for portable applications. Through patented technology, total amplifier power is shared across all output channels, allowing installers the freedom to utilize power where needed. With support for both low- and high-impedance loads up to 100V, PowerShare amplifiers adapt to a wide range of applications. Onboard configurable loudspeaker processing eliminates the need for an additional signal processor in many installations, while outstanding audio performance and reliability are assured with patented technologies inherited from the field-proven PowerMatch® line. This unique set of features and technologies makes PowerShare one of the most versatile high-performance amplifiers available.




• PowerShare Technology – Patented PowerShare technology allows the total 600 watts of power to be shared asymmetrically across all outputs, as each output is capable of delivering full power. Instead of selecting amplifier power based on the needs of the largest zone, installers now have the freedom to use total amplifier power in the application. This enables more flexibility during the initial design, or later on-site when making unplanned changes that take advantage of surplus power. 

• Load-Independent Outputs – Each channel can be configured for lowimpedance (4-8 Ω) or high-impedance (70/100V) applications without bridging, use of jumpers, or software settings. 

• DFL™ System – The Dual Feedback Loop system, inherited from the fieldproven Bose PowerMatch® amplifier line, improves performance and reliability through continuous monitoring and control of both the current and voltage delivered to each output load. This combination provides improved linearity and lower distortion, while protecting loudspeakers. 

• Integrated Loudspeaker Processing with Optional PowerShare Editor Configuration – For applications requiring additional signal processing the PowerShare Editor Software offers real-time selection and control of Bose loudspeaker EQs, 9-band PEQs, standard mixing, crossover, delay, and mute/ output polarity through a USB connection. For basic setups without a PC, rear-panel settings allow installers to recall Bose loudspeaker equalization and protection per output channel. These features eliminate the need for an external signal processor in many applications.




Power Rating


Amplifier Power

2 x 300 W (THD+N < 0.04%, 1 kHz, 4-8 Ω, 70/100V)

Maximum Power per Channel

600 W @ 4-8 Ω, 70/100V

Gain (Low-Z mode)

44 dB, RCA (unbalanced) inputs; 32 dB, XLR/TRS (balanced) inputs

Gain (70V mode)

47 dB, RCA (unbalanced) inputs; 35 dB, XLR/TRS (balanced) inputs

Gain (100V mode)

50 dB, RCA (unbalanced) inputs; 38 dB, XLR/TRS (balanced) inputs

Audio Performance


Frequency Response

4-8 Ω: 20 Hz – 20 kHz (+/- 0.5 dB @ 1 W) 70/100V: Same as 4-8 Ω with 50 Hz high-pass filter

Channel Separation (Crosstalk)

> 85 dB @ 1 kHz, > 65 dB @ 20 kHz

Signal to Noise Ratio

100 dB (at rated power, A-weighted)

Audio Inputs


Input Channels

2 unbalanced, 2 balanced



Input Impedance

10 kΩ (RCA), 20 kΩ (XLR/TRS)

Maximum Input Level

20 dBu (at 12 dBu sensitivity setting)


-10 / -2 dBV, RCA inputs; 4 / 12 dBu, XLR/TRS inputs (low / high sensitivity)

Audio Outputs





NL4 & binding posts

Integrated DSP


A/D and D/A Converters

24-bit / 48 kHz

Processing Functions

Standard mixer, loudspeaker EQ, 9-band PEQ, Vpeak/Vrms limiters, delay, band pass, mute/output polarity inversion

Loudspeaker Presets

Flat, DS16, DS40, DS100, FS3B, 402, 802, MA12EX, RMU105 and RMU108

Audio Latency

1 ms (any input to speaker output)

Indicators and Controls


Power LED

Solid green: Power is on. Blinking green: Unit is in standby mode. Solid amber: Thermal fault. Solid red: Supply fault.

Input Signal LED

Green: Signal present. Amber: Input is near clipping. Red: Input is clipping. Solid red: Indicates a fault.

Output Limit LED

Amber: Amplifier limiting an output. Blinking red: Amplifier muted. Solid red: Indicates a fault.

Controls, Front Panel

Power On/Off, Output Level Control

Controls, Rear Panel

Amplifier mode DIP switches, loudspeaker EQ dials



Mains Voltage

100 VAC – 240 VAC (±10%, 50/60 Hz)

AC Power Consumption

120 VAC: 79 W (Standby), 124 W (Max)

 230 VAC: 88 W (Standby), 184 W (Max)

Mains Connector

Standard IEC (C14)

Maximum Inrush Current

14.14 A (230 VAC / 50 Hz), 8.04 A (120 VAC / 60 Hz)


High temperature, output short, extra high frequency (EHF), excessively low or high AC line voltage



Dimensions (H x W x D)

44 mm x 483 mm x 414 mm (1.7” x 19.0” x 16.3”)

Shipping Weight

6.9 kg (15.3 lb)

Net Weight

5.5 kg (12.2 lb)

Cooling System

Microprocessor controlled, variable speed fans, left to right air flow



Inputs (Control)

USB input for configuring the amplifier with PowerShare Editor software. Mute input control



Similar Products


Emix EMPR3306 Universal Pre Ampl...


IVA M5.0MKII 2x350W with LCD Powe...


Audio Center Pro6.0 2x56...


Alto MAC2.4 2x560W Power Amplifi...


Wharfedale MP2800S Power A...


Peavey IPR2 2000 DSP 2x300W Cl...

See Also : Power Amplifier, Bose